Midea FT30-8MB 12-Inch Electric Table Fan
MODEL: FT30-8MB
CAUTION
Read Rules for Safe Operation and Instructions Carefully.
WARNING
- If the supply cord is damaged, it must be replaced by manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
- To protect against the risk of electrical shock, do not immerse the unit, cord or plug in water or other liquid.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Young children should be supervised to ensure that they do not play with the appliance.
- When the appliance is not in use and before cleaning, unplug the appliance from the outlet.
- Keep electrical appliances out of reach from Children or infirm persons. Do not let them use the appliances without supervision.
- When the fan was assembled, the rotor blade guard shall not be taken off anymore
- Prior cleaning unplug the fan.
- The rotor guard shall not be dissembled/opened to clean the rotor blades.
- Wipe the fan enclosure and rotor blade guard with a slightly damp cloth.
RULES FOR SAFE OPERATION
- Never insert fingers, pencils, or any other object through the grille when fan is running.
- Disconnect fan when moving from one location to another.
- Be sure fan is on a stable surface when operating to avoid overturning.
- DO NOT use fan in window, rain may create electrical hazard.
- Household use only.
PART
- Front grill
- Blade
- Plastic nut
- Rear grill
- Motor shaft
- Oscillating clutch knob
- Pedestal
- Screw
- Spinner
- Base
- Nut
- Piano switch
ASSEMBLY OF BASE
- Detach screw from base of the fan.
- Match locking tab to base and click into position.
- Tighten the screw in the base to secure the fan to the base.
GRILL & FAN BLADE ASSEMBLY
- Unscrew the spinner clockwise (or take the spinner out from the bag) and the plastic nut counterclockwise to remove both of them. Fix the rear grill to the motor then tighten the plastic nut again. (Fig.1)
- Insert the blade into shaft, and make sure the rotor shaft pin is fitted into groove of the blade. Turn the spinner counterclockwise to tighten the blade. (Fig.2)
- Open the clips on the Front Guard and place the Front Guard onto the
Rear Guard (align the locking screw holes) and close clips. Secure both guards firmly by fitting and tightening the locking screw and nut. (Fig.3)
OPERATION INSTRUCTION
Speed control
Speed is controlled by the piano switch. (0-1-2-3)
0–Off 1–Low 2—Medium 3—High
Oscillation control
To make the fan oscillate, push down on the oscillating clutch knob located on the top of the motor housing.
To stop the fan down from oscillating in the position desired, push on the oscillating clutch knob once more.
Tilting control
To adjust the air flow upward or downward, push the grilles lightly to the desired direction.
MAINTENANCE INSTRUCTION
The fan requires little maintenance. Do not try to fix it by yourself. Refer it to qualified service personnel if service is needed.
- Before cleaning and assembling, fan must be unplugged.
- To ensure adequate air circulation to the motor, keep vents at the rear of the motor free of dust. Do not disassemble the fan to remove dust.
- Please wipe the exterior parts with a soft cloth soaking a mild detergent.
- Do not use any abrasive detergent or solvents to avoid scratching the surface. Do not use any of the following as a cleaner: gasoline, thinner.
- Do not allow water or any other liquid into the motor housing or interior parts.
CLEANING
- Be sure to unplug from the electrical supply source before cleaning.
- Plastic parts should be cleaned with a soft cloth moisten with mild soap. Thoroughly remove soap film with dry cloth.
DISPOSAL：
Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your local government for information regarding the collection systems
available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being.