Europrolav 12-150 Petrol High-Pressure Washer
USER MANUAL
IMPORTANCE OF THE MANUAL
This manual is a key part for the use of your machine. It summarizes the procedures of starting up, cleaning and maintenance of the device and also the safety instructions you need to observe. Read carefully all the working and safety instructions and the warnings included in this manual before starting your machine. Most of the accidents are caused by non-compliance of the safety standards and rules. This manual must be kept near the machine, within reach of the user and held in good condition until the final destruction of the machine. In case of loss or deterioration of the manual, you can ask the machine manufacturer mentioned on page 4 for a copy at any moment.
RECEIVERS OF THE MANUAL
This manual is intended to any staff which will manipulate the machine :
- people in charge of the transport of the machine
- people in charge of the use of the machine
- people in charge of the cleaning and maintenance of the machine
- people in charge of the final destruction of the machine
WARNING
SAFETY
Using the machine in an incorrect way or in non-compliance of the safety instructions indicated in this manual can cause death or serious injuries. Read carefully all the working and safety instructions and the warnings contained in this manual before starting your machine.
- Respect all the safety standards before running the equipment.
- Use the equipment only for the applications specified in the manual.
- Always remain alert when using the equipment.
- Transport the machine using the handles or the appropriate grips.
- During the breaks, remember to turn off the machine.
- Let at least 50 cm of free space between the equipment and any obstacle so that the air flow is not blocked.
- Know how to quickly stop the equipment in case of necessity.
- Never use the equipment while it is running abnormally or it is defective.
- Do not direct a water jet or flammable liquid on the machine.
- Never direct an air jet or product jet on a person or an animal.
- Do not touch warm surfaces of the equipment.
- Always wear adequate body protections (glasses, gloves, overall and mask) and pay attention to long hair.
- Never touch moving parts.
- Do not insert any object or the hands inside the protection grids to avoid any accident or damage to the machine.
- For any outside job, only use appropriate extension cords.
- Maintain the equipment carefully and clean it properly after every use.
- Avoid absolutely to unscrew any connection while the machine is under pressure.
- Check the damaged parts.
- Do not clean the plastic parts with solvant.
- In case of needed After-Sale Service, always specify the machine model and its serial number.
- For any replacement of parts, only use genuine parts.
- Do not modify the machine.
- Do not cut or dismantle the protection grids.
WORKSPACE
- Maintain the workspace clean and clear.
- The ambient operating temperature must be from 5°C and 35°C.
- Do not use the equipment in a potentially explosive area.
- Do not place any potentially inflammable objects in close proximity to the machine.
- Take away every not qualified person from the working area of the machine, as well as children and animals.
- In case of installation of the machine on scaffolding or a plan above ground level, attach the machine to avoid any fall while operating.
- Do not install the equipment on an inclined surface to avoid the risks of unexpected moves or falls.
HOSES
- Always use hoses and connectors (original parts) with appropriate maximum pressure characteristics, do not attempt to repair them.
- Do not walk on the hoses, do not bend them.
- Do not use the hoses to pull the machine.
STORAGE
Keep the equipment in a clean and clear area in which the temperature does not exceed +35°C.
WARNING: The machine must not be stored in an area with a temperature lower than 0°C, otherwise the water remaining in the pump may freeze. IN CASE OF NECESSITY, WE SAVE OURSELVES THE RIGHT TO MAKE ANY USEFUL MODIFICATION WITHOUT ADVANCED NOTICE.
END OF LIFE OF THE PRODUCT
At its end of life, the machine must not be eliminated with the other household waste. The uncontrolled elimination of waste can harm the environment or human health. Individuals are invited to contact the distributor which sold them the product or to inquire with their city hall to know where and how to get rid of the product so it can be recycled while respecting the environment. For any further information, please contact our hotline to [email protected] or +33 4 42 29 08 96.
YOUR MACHINE
DESCRIPTION
EUROPROLAV washers are powerful and robust washers. They are suitable for use on any type of job. They are equipped with places to roll up the water inlet and lance hoses. With large diameter wheels and a reinforced chassis, they are very maneuverable and designed for easy maintenance. The 12-150 TH and 15-200 TH.2 models are also equipped with detergent suction.
TECHNICAL CHARACTERISTICS
| 12-150 TH
Vanguard |
15-200 TH
Kohler |
15-200 TH
Honda |
15-250 TH
Honda |
18-280 TH
Honda |
|
| Variable pressure | 0 to 150 bar | 0 to 200 bar | 0 to 250 bar | 0 to 280 bar | |
| Flow-rate | 12 L/min | 15 L/min | 18 L/min | ||
| Nozzle | 15°- 30 | 15°- 45 | 15°- 40 | 15°- 40 | |
| Motor power | VANGUARD 6,5 HP | KOHLER 9,5 HP | HONDA 13 HP | ||
| Fuel used | unleaded 98 | ||||
| Tank capacity | 4,1 L | 7,3 L | 7,9 L | ||
| Consumption | 1,6 L/h | 2,2 L/h | 3,4 L/h | 3,78 L/h | |
| Lubrication | splashing | ||||
| Pump | brass head, 3 ceramic pistons | ||||
| Detergent suction system | yes | no | |||
| Pump rotation | 3400 RPM | 3600 RPM | 1450 RPM | ||
| Max. water temperature | 70°C | ||||
| Lance | double with KW coupling | ||||
| Hose | 10 m – 315 bar | 20 m – 315 bar | |||
| Dimensions (L x w x h) | 66 x 62 x 91 cm | ||||
| Weight | 43 kg | 66 kg | 68 kg | 77 kg | 79 kg |
IDENTIFICATION OF THE COMPONENTS 
| A | Water supply hose (not supplied on model 12-150TH) |
| B | Lance |
| C | Engine |
| D | High pressure hose |
| E | Pump |
| F | By-pass |
| G | Manometer |
| H | High pressure outlet connection |
| I | Water inlet quick coupler |
| J | Oil level cap |
USE OF THE MACHINE
PREREQUISITES
- The connection to the water supply must be made on an inlet with a sufficient flow rate, with a minimum Ø19 hose to be connected to the pump’s quick coupling.
- The high pressure hose is connected to the connection at the pump by-pass outlet.
- The engine must be stopped when filling the fuel tank.
Before each use of the washer, check the engine and pump oil levels using the dipsticks intended for this purpose. - Never operate the washer without a water supply, as this could cause serious damage to the pump.
- The temperature of the water used must not exceed +60°C.
Do not use the washer in a closed room or in an area where the temperature is below 0°C.
STARTING UP
- Check the oil level and then turn the engine button to the ON position.
- After connecting the washer to the water supply, open the water supply completely.
- Press the trigger on the lance, water will come out of the nozzle at low pressure.
- After making sure the tank contains gasoline, open the fuel supply.
- Engage the starter.
- Put the accelerator on full throttle.
- Start the engine by pulling on the starter, with the trigger held in.
- Release the trigger and let the engine warm-up for a few moments.
- Turn the starter off.
- The cleaner is ready for use. To adjust the working pressure, turn the black knob on the by-pass and check the pressure set on the manometer.
ENGINE SHUTDOWN
Turn the button to the OFF position and shut off the fuel supply.
After each engine shutdown, it is important to relieve the pressure remaining in the hose. To do this, press the trigger on of the lance.
DEFECTS AND REMEDIES
Before loosening the hose, make sure it is no longer under pressure.
| Defect | To check | Remedy |
|
Abnormal pressure oscillations |
• The pump sucks air. | • Check the suction hoses. |
| • Water supply filter worn, dirty
or clogged. |
• Clean or change the filter. | |
| The pump operates without
reaching the required pressure |
• Unsuitable or worn nozzle. | • Change the nozzle. |
| • Worn gaskets. | • Change the gaskets. | |
|
Pressure drops |
• Worn nozzle. | • Change the nozzle. |
| • Worn valve. | • Change the valve. | |
| • Dirty water supply filter. | • Clean or change the filter. | |
| • Adjustment by-pass worn or
clogged. |
• Clean or change the by-pass. | |
| • Worn gaskets. | • Change the gaskets. | |
|
Abnormal noise |
• Air suction. | • Check the suction hoses. |
| • Worn or dirty bypass. | • Clean or change the by-pass. | |
| • Worn bearings. | • Change the bearings. | |
| Oil leaks | • Worn oil gaskets. | • Change gasket kit. |
| Water in oil | • Worn oil or water gaskets. | • Change gasket kit. |
| Water leakage from the lance | • Worn seals. | • Change gasket kit. |
DECLARATION OF CONFORMITY
COMPLIES WITH THE THE DIRECTIVES:
- Machines 2006/42/CE
- CEM 2014/30/UE
- ROHS 2011/65/UE
- Noise emissions 2005/88/CE
WARRANTY CONDITIONS
Each piece of equipment is delivered inspected and tested. We exclude any warranty for visible defects, not notified by the customer within 48 hours. The equipment sold is guaranteed during the manufacturer’s warranty from the date of purchase, as specified on the original proof of purchase, and under the conditions defined by the manufacturer. This warranty covers any equipment against any manufacturing or material defect, under normal conditions of use. Insofar as the customer is presumed to be a professional of the same field of specialty, this warranty covers only the defect of conception of the equipment rendering it unfit for its use, which could not be detected by a professional buyer. The defects or deteriorations caused by natural wear, external accident or a modification, use, storage or treatment of the equipment not planned by the manufacturer, nor specified by ourselves, are excluded from any warranty.
Are expressly excluded from the warranty the defects resulting from improper use, the application of abrasive or corrosive products, an inappropriate installation, the negligence, an insufficient maintenance or cleaning, inappropriate conditions of storage, chemical, electronic or electric influences, any change in the normal process of use. The following wearing parts are not covered by the warranty (non-exhaustive list): rotors, stators, driving shafts, connecting rods, seals, cleaning balls, spray guns, lance, nozzle, hose, needle kits, cylinders, piston rods, prime/spray valve assy, seal kits, membranes, suction and delivery valves, carding machine vanes, filters, oils, chains and quick-release clip. The warranty also excludes the equipment on which the serial number was erased or made illegible, on which unauthorized people made attempts of repair, which were totally or partially dismantled.
Our equipment are covered by a manufacturer’s warranty (parts and labor) of 12 months following the purchase date by the final customer, without exceeding 24 months from the date of purchase by the client. The final user can extend this manufacturer’s warranty for a further 12 months by filling in the warranty extension form on our website www.euromair.com (under After-Sale Service) within 4 weeks of purchase.
This manufacturer’s warranty and its extension shall automatically cease if the customer does not resell the equipment within 24 months of its purchase. The cases of exclusion of warranty mentioned in articles above are also applicable to our own equipment.
The manufacturer’s warranty shall always be subject to the presentation of the purchase invoice. If the defective equipment is covered by the manufacturer’s warranty, it shall be repaired or replaced at our discretion free of charge. If the defective equipment is not covered by the manufacturer’s warranty, we shall issue a quote for the repair that we shall submit to the customer for approval. Except as otherwise required by law, this manufacturer’s warranty is exclusive of all other warranties, including the statutory warranty of hidden defects. In case of intervention of our services on a breakdown caused by the customer or an incident excluded in the conditions referred to above, the costs of repair and transport shall be invoiced to the customer. We exclude all liability for indirect damages suffered by the customer, such as, but not limited to, loss of income, turnover, loss of profits, loss of image, of any kind whatever.In all cases, our liability shall be limited to the amount paid by the customer for non-compliant equipment. Any legal action of the customer against us relating to the warranty of the equipment shall be barred 1 year after the date of discovery of the defect. The customer shall have to prove the date of this discovery.
Request for Warranty
For any request related to the repair of equipment covered by the manufacturer’s warranty, the customer shall have to fill the warranty form, available on our website to the following address: https://www.euromair.com/en/after-sales-service/. For a full dossier, the following documents shall have to be attached:
- the purchase invoice of the final user
- pictures of the defective parts of the equipment
- a description of the breakdown
- the quote of labor if the customer is certified by EUROMAIR for repairing the equipment No invoice of labor shall be taken into account without our prior approval.
Analysis of the breakdown by our technical department
A file number shall be given to the customer and an answer shall be provided within 48 working hours after the reception, provided that the request for warranty is considered as full.
In the event the equipment is covered by the manufacturer’s warranty, we shall confirm the warranty to the customer and send him a quote (without price) detailing the parts to be changed and any comments.
Return of replacement parts
Replacement parts must be ordered with a warranty agreement number and will be made available to the customer at our factory. The conditions of return of the equipment are detailed in our Delivery terms. In the case of a warranty claim on an on-board component such as a Kohler, Honda or Vanguard engine in a machine manufactured by us, only the manufacturer of the component is able to validate the warranty coverage. In this case, the request must be addressed directly to the manufacturer of the component or to its nearest authorized representative. The Euromair, Euromair MPC or Mixer service centers may be considered as the manufacturer’s representatives if they are the closest. As this principle also applies to batteries, our supplier Parts Holding Europe, or one of its sister companies, remains your contact for your requests
(https://www. partsholdingeurope.com/).