CHAMPION Portable Inverter Generator Owner’s Manual

Contents hide

1 Portable Inverter Generator

2 Documents / Resources

2.1 References

Portable Inverter Generator

View Fullscreen

OWNER’S MANUAL & OPERATING INSTRUCTIONS

2000 Starting Watts / 1700 Running Watts
PORTABLE INVERTER GENERATOR

US Patent # D656897, 8391012
SAVE THESE INSTRUCTIONS Important Safety Instructions are included in this manual.

Li da

ty Ga

3mited War r an

Yea r ·
n t ía

Añ os
Limi

MODEL NUMBER
73536i

REV 73536i-20200730

12039 Smith Ave. Santa Fe Springs CA 90670
USA / 1-877-338-0999 www.championpowerequipment.com

FCC Statement
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and
receiver. Connect the equipment into an outlet on a
circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

Have questions or need assistance?
Do not return this product to the store!
WE ARE HERE TO HELP!

Visit our website:
www.championpowerequipment.com
for more info:

· Product Info & Updates

· Tech Bulletins

· Frequently Asked Questions · Product Registration

or
Call our Customer Care Team Toll-Free at:
1-877-338-0999

*We are always working to improve our products. Therefore, the enclosed product may differ slightly from the image on the cover.

73536i

2000 Starting Watts / 1700 Running Watts
PORTABLE INVERTER GENERATOR

TABLE OF CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Portable Power Generator . . . . . . . . . . . . . . . . . 1 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . 1 This Booklet . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Manual Conventions. . . . . . . . . . . . . . . . . . . . . . . 2 Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Controls and Features . . . . . . . . . . . . . . . . . . . . . 5
Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Power Panel . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Parts Included . . . . . . . . . . . . . . . . . . . . . . . . 6 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Remove the Generator from the Shipping Carton . 7 Add Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . 7 Add Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Generator Location . . . . . . . . . . . . . . . . . . . . . 9 Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Starting the Engine . . . . . . . . . . . . . . . . . . . . . 9 Connecting Electrical Loads . . . . . . . . . . . . . . 10 Economy Control Switch. . . . . . . . . . . . . . . . . 10 12V DC Outlet . . . . . . . . . . . . . . . . . . . . . . . 11 Stopping the Engine . . . . . . . . . . . . . . . . . . . 11 Do Not Overload Generator . . . . . . . . . . . . . . . 12
Capacity . . . . . . . . . . . . . . . . . . . . . . . . . 12 Power Management . . . . . . . . . . . . . . . . . . 12 Overload Operation . . . . . . . . . . . . . . . . . . . . 12 Parallel Operation . . . . . . . . . . . . . . . . . . . . . 12

Maintenance and Storage . . . . . . . . . . . . . . . . . . 13 Engine Maintenance . . . . . . . . . . . . . . . . . . . 13 Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . 13 Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . 14 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . 14 Spark Arrester Cleaning . . . . . . . . . . . . . . . 14 Adjustments . . . . . . . . . . . . . . . . . . . . . . . 15 Maintenance Schedule. . . . . . . . . . . . . . . . 15 Generator Maintenance . . . . . . . . . . . . . . . . . 15 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Generator Storage . . . . . . . . . . . . . . . . . . . 15
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Engine Specifications . . . . . . . . . . . . . . . . . . 17 Generator Specifications . . . . . . . . . . . . . . . . 17 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . . . 17 Maintenance Valve Clearance . . . . . . . . . . . . . 17
An Important Message About Temperature . . . . 17 Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . 18 Parts Diagram. . . . . . . . . . . . . . . . . . . . . . . . 19 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Engine Parts Diagram . . . . . . . . . . . . . . . . . . 21 Engine Parts List . . . . . . . . . . . . . . . . . . . . . 22 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . 23

INTRODUCTION

ENGLISH 73536i

Introduction
Congratulations on your purchase of a Champion Power Equipment inverter generator. CPE designs and builds generators to strict specifications. With proper use and maintenance, this generator will bring years of satisfying service.

Accessories
Champion Power Equipment manufactures and sells accessories designed to help you get the most from your purchase. To find out more about our covers and power cables, please visit our web site at:
www.championpowerequipment.com

Portable Power Generator
This unit is a gasoline engine driven, alternating current (AC) generator. It is designed to supply electrical power for lighting, appliances, tools and similar equipment.

This Booklet
Every effort has been made to ensure the accuracy and completeness of the information in this manual. We reserve the right to change, alter and/or improve the product and this document at any time without prior notice.

Record the model and serial numbers as well as date and place of purchase for future reference. Have this information available when ordering parts and when making technical or warranty inquiries.

Champion Power Equipment Support
1-877-338-0999
Model Number
73536i
Serial Number

Date of Purchase

Purchase Location

For Oil Type see `Add Engine Oil` section. For Fuel Type see `Add Fuel` section.

73536i ENGLISH

MANUAL CONVENTIONS

This manual uses the following symbols to help differentiate between different kinds of information. The safety symbol is used with a key word to alert you to potential hazards in operating and owning power equipment. Follow all safety messages to avoid or reduce the risk of serious injury or death.

DANGER

CAUTION

DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

CAUTION used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage.

WARNING
WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION
CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

NOTE
If you have questions regarding your generator, we can help. Please call our help line at 1-877-338-0999

SAFETY RULES
WARNING
Read this manual thoroughly before operating your generator. Failure to follow instructions could result in serious injury or death.
DANGER
Generator exhaust contains carbon monoxide, a colorless, odorless, poison gas. Breathing carbon monoxide will cause nausea, dizziness, fainting or death. If you start to feel dizzy or weak, get to fresh air immediately.
Operate generator outdoors only in a well ventilated area. DO NOT operate the generator inside any building, including garages, basements, crawlspaces and sheds, enclosure or compartment, including the generator compartment of a recreational vehicle. DO NOT allow exhaust fumes to enter a confined area through windows, doors, vents or other openings. DANGER CARBON MONOXIDE: using a generator indoors CAN KILL YOU IN MINUTES.
DANGER
Rotating parts can entangle hands, feet, hair, clothing and/or accessories. Traumatic amputation or severe laceration can result.
Keep hands and feet away from rotating parts. Tie up long hair and remove jewelry. Operate equipment with guards in place. DO NOT wear loose-fitting clothing, dangling drawstrings or items that could become caught.
WARNING
Operation of this equipment may create sparks that can start fires around dry vegetation. A spark arrestor may be required. The operator should contact local fire agencies for laws or regulations relating to fire prevention requirements.
3

ENGLISH 73536i
DANGER
Generator produces powerful voltage.
DO NOT touch bare wires or receptacles. DO NOT use electrical cords that are worn, damaged or frayed. DO NOT operate generator in wet weather. DO NOT allow children or unqualified persons to operate or service the generator Use a ground fault circuit interrupter (GFCI) in damp areas and areas containing conductive material such as metal decking. Use approved transfer equipment to isolate generator from your electric utility and Notify your utility company before connecting your generator to your power system.
WARNING
Sparks can result in fire or electrical shock.
When servicing the generator:
Disconnect the spark plug wire and place it where it cannot contact the plug. DO NOT check for spark with the plug removed. Use only approved spark plug testers.
WARNING
Running engines produce heat. Severe burns can occur on contact. Combustible material can catch fire on contact.
DO NOT touch hot surfaces. Avoid contact with hot exhaust gases. Allow equipment to cool before touching. Maintain at least 3 ft. (91.4 cm) of clearance on all sides to ensure adequate cooling. Maintain at least 5 ft. (1.5 m) of clearance from combustible materials.
WARNING
Medical and Life Support Uses.
In case of emergency, call 911 immediately. NEVER use this product to power life support devices or life support appliances. NEVER use this product to power medical devices or medical appliances. Inform your electricity provider immediately if you or anyone in your household depends on electrical euipment to live. Inform your electrical provider immediately if a loss of power would cause you or anyone in your household to experience a medical emergency.

73536i ENGLISH
DANGER
Fuel and fuel vapors are highly flammable and extremely explosive. Fire or explosion can cause severe burns or death. Unintentional startup can result in entanglement, traumatic amputation or laceration.
When adding or removing fuel:
Turn the generator off and let it cool for at least two minutes before removing the fuel cap. Loosen the cap slowly to relieve pressure in the tank. Only fill or drain fuel outdoors in a well-ventilated area. DO NOT pump gas directly into the generator at the gas station. Use an approved container to transfer the fuel to the generator. DO NOT overfill the fuel tank. Always keep fuel away from sparks, open flames, pilot lights, heat and other sources of ignition. DO NOT light or smoke cigarettes.
When starting the generator:
DO NOT attempt to start a damaged generator. Make certain that the gas cap, air filter, spark plug, fuel lines and exhaust system are properly in place. Allow spilled fuel to evaporate fully before attempting to start the engine. Make certain that the generator is resting firmly on level ground.
When operating the generator:
DO NOT move or tip the generator during operation. DO NOT tip the generator or allow fuel or oil to spill.
When transporting or servicing the generator:
Make certain that the fuel shutoff valve is in the off position and the fuel tank is empty. Disconnect the spark plug wire.
When storing the generator:
Store away from sparks, open flames, pilot lights, heat and other sources of ignition.
WARNING
Cancer and Reproductive Harm www.P65Warnings.ca.gov

SAFETY RULES
WARNING
Rapid retraction of the starter cord will pull hand and arm towards the engine faster than you can let go. Unintentional startup can result in entanglement, traumatic amputation or laceration. Broken bones, fractures, bruises or sprains could result.
When starting engine, pull the starter cord slowly until resistance is felt and then pull rapidly to avoid kickback. DO NOT start or stop the engine with electrical devices plugged in.
CAUTION
Exceeding the generator’s running capacity can damage the generator and/or electrical devices connected to it.
DO NOT overload the generator. Start the generator and allow the engine to stabilize before connecting electrical loads. Connect electrical equipment in the off position, and then turn them on for operation. Turn electrical equipment off and disconnect before stopping the generator. DO NOT tamper with the governed speed. DO NOT modify the generator in any way.
CAUTION
Improper treatment or use of the generator can damage it, shorten its life and void your warranty.
Use the generator only for intended uses. Operate only on level surfaces. DO NOT expose generator to excessive moisture, dust, or dirt. DO NOT allow any material to block the cooling slots. If connected devices overheat, turn them off and disconnect them from the generator. DO NOT use the generator if: Electrical output is lost Equipment sparks, smokes or emits flames Equipment vibrates excessively

CONTROLS AND FEATURES

ENGLISH 73536i

Read this owner’s manual before operating your generator. Familiarize yourself with the location and function of the controls and features. Save this manual for future reference.

Generator

5 7

(1) Carrying Handle (2) Fuel Lever Vent Turn this valve to the “On”
position to supply air to the tank. (3) Fuel Cap Remove to add fuel. (4) Recoil Starter Used to start the engine.

(5) Spark Plug Access Cap (6) Maintenance Cover Oil filler, Air filter, and
Carburetor access. (7) Muffler

73536i ENGLISH

CONTROLS AND FEATURES

Power Panel

123

6 7

9
8 13

* These outlets are used for connecting two Champion model 73536i generators for parallel operation. A Champion model 73500i cable kit (optional equipment) is required for parallel operation.

(1) Oil Warning Light Check oil level when this light turns on. Engine will not run when indicator is lit.
(2) Overload Indicator Light This light turns ON when the generator is overloaded and will cut power to the receptacles.
(3) Output Light Remains ON during normal operating conditions. Shuts OFF when generator is overloaded.
(4) Economy Control Switch
(5) Engine Switch
(6) Choke Knob
(7) Fuel Valve Knob
(8) Parallel Operation Control*
(9) 120 Volt AC, 20 Amp Duplex (NEMA 5-20R) May be used to supply electrical power for the operation of 120 Volt AC, 20 Amp, single phase 60 Hz electrical loads.
(10) Parallel Operation Outlets*
(11) Circuit Breaker Protects the generator against electrical overload.
(12) 12V DC 8A Outlet Use this outlet to charge 12V automotive type batteries ONLY.
(13) Ground Terminal Consult an electrician for local grounding regulations.

Parts Included
Your 73536i Gasoline Powered Generator ships with the following parts:
12V DC Battery Charging Cable. . . . . . . . . . . . . . 1 Spark Plug Socket . . . . . . . . . . . . . . . . . . . . . . . 1 Oil Funnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.4 L

ASSEMBLY

ENGLISH 73536i

Your generator requires some assembly. This unit ships from our factory without oil. It must be properly serviced with fuel and oil before operation. If you have any questions regarding the assembly of your generator, call our help line at 1-877-338-0999. Please have your serial number and model number available.

Add Engine Oil Cont’d.
4. Add 0.4 qt. (0.4 L) of oil (included) and replace oil fill cap/dipstick. Check engine oil level daily and add as needed. DO NOT OVERFILL.
Degrees Celsiusº (Outside)

Remove the Generator from the Shipping Carton
1. Set the shipping carton on a solid, flat surface. 2. Remove everything from the carton except the
generator. 3. Using the handle of the unit, carefully remove the
generator from the box.
Add Engine Oil
CAUTION
DO NOT attempt to crank or start the engine before it has been properly filled with the recommended type and amount of oil. Damage to the generator as a result of failure to follow these instructions will void your warranty.
1. Place the generator on a flat, level surface. 2. Loosen the cover screw and remove the maintenance
cover.

Full Synthetic 5W-30
Degrees Fahrenheitº (Outside)
5. Check engine oil level daily and add as needed.
CAUTION
The engine is equipped with a low oil shut-off and will stop when the oil level in the crankcase falls below the threshold level.
NOTE
The recommended oil type is 10W-30 automotive oil.

NOTE
Check oil often during the break-in period. Refer to the Maintenance section for recommended service intervals.

3. Remove oil fill cap/dipstick to add oil.

73536i ENGLISH

ASSEMBLY

Add Fuel
1. Use clean, fresh, regular unleaded fuel with a minimum octane rating of 87 and an ethanol content of less than 10% by volume.
2. DO NOT mix oil with fuel. 3. Clean the area around the fuel cap. 4. Remove the fuel cap. 5. Slowly add fuel to the tank. DO NOT OVERFILL.
Fuel can expand after filling. A minimum of ¼ in. (6.4 mm) of space left in the tank is required for fuel expansion, more than ¼ in. (6.4 mm) is recommended. Fuel can be forced out of the tank as a result of expansion if it is overfilled, and can affect the stable running condition of the product. When filling the tank, it is recommended to leave enough space for the fuel to expand.
6. Screw on the fuel cap and wipe away any spilled fuel.
CAUTION
Use regular unleaded gasoline with a minimum octane rating of 87.
Do not mix oil and gasoline. Fill tank to approximately ¼ in. (6.4 mm) below the top of the tank to allow for fuel expansion. DO NOT pump gas directly into the generator at the gas station. Use an approved container to transfer the fuel to the generator. DO NOT fill fuel tank indoors. DO NOT fill fuel tank when the engine is running or hot. DO NOT overfill the fuel tank. DO NOT light cigarettes or smoke when filling the fuel tank.

Add Fuel Cont’d.
NOTE
Our engines work well with 10% or less ethanol blend fuels. When using blended fuels there are some issues worth noting: Ethanol-gasoline blends can absorb more water
than gasoline alone. These blends can eventually separate, leaving
water or a watery goo in the tank, fuel valve and carburetor. With gravity-fed fuel supplies, this compromised fuel can be drawn into the carburetor and cause damage to the engine and/or potential hazards. There are only a few suppliers of fuel stabilizer that are formulated to work with ethanol blend fuels. Any damages or hazards caused by using improper fuel, improperly stored fuel, and/ or improperly formulated stabilizers, are not covered by manufacture’s warranty. It is advisable to always shut off the fuel supply, run the engine to fuel starvation and drain the tank when the equipment is not in use for more than 30 days.
Grounding
Your generator must be properly connected to an appropriate ground to help prevent electric shock.
WARNING
Failure to properly ground the generator can result in electric shock.
A ground terminal connected to the frame of the generator has been provided on the power panel. For remote grounding, connect of a length of heavy gauge (12 AWG minimum) copper wire between the generator ground terminal and a copper rod driven into the ground. We strongly recommend that you consult with a qualified electrician to ensure compliance with local electrical codes.

WARNING
Pouring fuel too fast through the fuel screen may result in blow back of fuel at the operator while filling.

OPERATION

ENGLISH 73536i

Generator Location
NEVER operate the generator inside any building, including garages, basements, crawlspaces and sheds, enclosure or compartment, including the generator compartment of a recreational vehicle. Please consult your local authority. In some areas, generators must be registered with the local utility. Generators used at construction sites may be subject to additional rules and regulations. Generators should be on a flat, level surface at all times. (Even while not in operation) Generators must have at least 5 ft. (1.5 m) of clearance from all combustible material. In addition to clearance from all combustible material, generators must also have at least 3 ft. (91.4 cm) of clearance on all sides to allow for adequate cooling, maintenance and servicing. Generators should never be started or operated in the back of a SUV, camper, trailer, in the bed of a truck (regular, flat or otherwise), under staircases/stairwells, next to walls or buildings, or in any other location that will not allow for adequate cooling of the generator and/or the muffler. DO NOT contain generators during operation. Allow generators to properly cool before transport or storage. Place the generator in a well-ventilated area. DO NOT place the generator near vents or intakes where exhaust fumes could be drawn into occupied or confined spaces. Carefully consider wind and air currents when positioning generator. Failure to follow proper safety precautions may void manufacturer’s warranty.

Grounding
The generator system ground connects the frame to the ground terminals on the power panel. The generator (stator winding) is isolated from the
frame and from the AC receptacle ground pin. Electrical devices that require a grounded receptacle
pin connection may not function properly.
Starting the Engine
1. Make certain the generator is on a flat, level surface. 2. Disconnect all electrical loads from the generator.
Never start or stop the generator with electrical devices plugged in or turned on. 3. Turn the fuel cap vent lever to the “On” position.
4. Turn the fuel valve to the “On” position.

WARNING
Do not operate or store the generator in rain, snow, or wet weather.
Using a generator or electrical appliance in wet conditions, such as rain or snow, or near a pool or sprinkler system, or when your hands are wet, could result in electrocution.

5. Pull the choke lever out when starting the generator.

WARNING
During operation the muffler and exhaust fumes produced will become hot. If adequate cooling and breathing space are not supplied, or if the generator is blocked or contained, temperatures can become extremely heated and may lead to fire.
9

73536i ENGLISH

OPERATION

Starting the Engine Cont’d.
6. Turn the engine switch to the “On” position.
7. Pull the starter cord slowly until resistance is felt and then pull rapidly.
8. As engine warms up, push the choke lever in.
NOTE
Keep choke lever in “Choke” position for only 1 pull of the recoil starter. After first pull, push the choke lever in for up to the next 3 pulls of the recoil starter. Too much choke leads to spark plug fouling/ engine flooding due to the lack of incoming air. This will cause the engine not to start.
NOTE
If the engine starts but does not run make certain that the generator is on a flat, level surface. The engine is equipped with a low oil sensor that will prevent the engine from running when the oil level falls below a critical threshold.

Connecting Electrical Loads
1. Let the engine stabilize and warm up for a few minutes after starting
2. Plug in and turn on the desired 120 Volt AC single phase, 60 Hz electrical loads.
DO NOT connect 3-phase loads to the generator. DO NOT connect 50 Hz loads to the generator. DO NOT overload the generator.
NOTE
Connecting a generator to your electric utility company’s power lines or to another power source may be against the law. In addition this action, if done incorrectly, could damage your generator and appliances and could cause serious injury or even death to you or a utility worker who may be working on nearby power lines. If you plan to run a portable electric generator during an outage, please notify your electric utility company immediately and remember to plug your appliances directly into the generator. Do not plug the generator into any electric outlet in your home. Doing so could create a connection to the utility company power lines. You are responsible for ensuring that your generator’s electricity does not feed back into the electric utility power lines. If the generator will be connected to a building electrical system, consult your local utility company or a qualified electrician. Connections must isolate generator power from utility power and must comply with all applicable laws and codes.
Economy Control Switch
The Economy Control switch can be activated in order to minimize fuel consumption and noise while operating the unit during times of reduced electrical output, allowing the engine speed to idle during periods of non-use. The engine speed returns to normal when an electrical load is connected. When the economy switch is off, the engine runs at normal speed continuously.
WARNING
For periods of high electrical load or momentary fluctuations, the Economy Control Switch should be turned OFF.

OPERATION

ENGLISH 73536i

12V DC Outlet
The 12V DC outlet is ONLY to be used with the supplied 12V battery charging cable. The DC output is unregulated and will damage other 12V DC products. When using the DC outlet, turn the Economy switch to the “OFF” position.
CAUTION
Do not start the vehicle while the battery charging cable is connected and the generator is running. It will not give the battery a boost of power. The vehicle or the generator may be damaged. Charge only vented wet lead acid batteries. Other types of batteries may burst, causing personal injury or damage.
NOTE
Be sure all electric devices including the lines and plug connections are in good condition before connection to the generator.
1. Before connecting the battery charging cable to a battery that is installed in a vehicle, disconnect the vehicle battery ground cable from the negative () battery terminal.
2. Plug the battery charging cable into the DC receptacle of the generator.
3. Connect the red (+) battery charger lead to the red (+) battery terminal.
4. Connect the black () battery charger lead to the black () battery terminal.
5. Start the generator.

Stopping the Engine
1. Turn off and unplug all electrical loads. Never start or stop the generator with electrical devices plugged in or turned on.
2. Let the generator run at no-load for several minutes to stabilize internal temperatures of the engine and generator.
3. Turn the Fuel Valve to the “OFF” position. 4. Let the engine run until fuel starvation has stopped
the engine. This usually takes a few minutes. 5. Press the engine switch to the “OFF” position. 6. Allow the generator to cool down completely to room
temperature 7. Turn the fuel cap lever vent to the “Off” position after
the generator has cooled down completely. Important: Always ensure that the Fuel Valve and the Engine Switch are in the “OFF” position when the engine is not in use.
NOTE
If the engine will not be used for a period of two (2) weeks or longer, please see the Storage section for proper engine and fuel storage.

WARNING
Do not operate a device while it is plugged in to the 12V DC outlet.
Prolonged exposure to engine exhaust can cause serious injury or death.

WARNING
While charging a device do no place on the exhaust side of the generator. Extreme heat caused by exhaust can damage the device, and cause a potential fire hazard.

73536i ENGLISH

OPERATION

Do Not Overload Generator
Capacity
Follow these simple steps to calculate the running and starting watts necessary for your purposes. 1. Select the electrical devices you plan on running at
the same time. 2. Total the running watts of these items. This is
the amount of power you need to keep your items running. 3. Identify the highest starting wattage of all devices identified in step 1. Add this number to the number calculated in step 2. Surge wattage is the extra burst of power needed to start some electric driven equipment. Following the steps listed under “Power Management” will guarantee that only one device will be starting at a time.
Power Management
Use the following formula to convert voltage and amperage to watts:
Volts x Amps = Watts
To prolong the life of your generator and attached devices, follow these steps to add electrical load: 1. Start the generator with no electrical load attached 2. Allow the engine to run for several minutes to stabilize. 3. Plug in and turn on the first item. It is best to attach
the item with the largest load first. 4. Allow the engine to stabilize. 5. Plug in and turn on the next item. 6. Allow the engine to stabilize. 7. Repeat steps 5-6 for each additional item.
NOTE
Never exceed the specified capacity when adding loads to the generator.
Overload Operation
The overload indicator light will turn on when the load exceeds 1750W. If the load exceeds 2000W, the light will blink and cut power to the receptacles. To recover the power, you must shut off the engine, wait 5 seconds, and restart the generator.

Parallel Operation
Two Champion model 73536i generators can be operated in parallel to increase the total available electrical power to 3000 watts. A Champion model 73500i parallel kit (optional equipment) is required for parallel operation. For kit availability, call Customer Service at 1-877-338-0999 or visit: www.championpowerequipment.com. Detailed instructions for parallel kit installation and operation of the connected generators are provided in the parallel kit Owner’s Manual and Operating Instructions. Please note the following important requirements: 1. The two generators may be stacked one on top of the
other by aligning the lower pads and upper pockets at each corner of the generators. 2. Disconnect or turn off all electrical loads from both generators. 3. The ECON switch must be in the same position on both generators. 4. Before starting the engines, connect the AC power outlet cables, the control cables and the ground cables to both generators. Follow the instructions supplied with the parallel kit. 5. Do not disconnect any cables after the engines have been started. 6. Start both engines and observe the green output indicator light on both generator panels. 7. Connect and turn on the electrical devices.
NOTE
The total electrical load attached to the parallel kit must not exceed 3400 watts.
8. Follow the instructions on the previous page for turning off the generators.

MAINTENANCE AND STORAGE

ENGLISH 73536i

The owner/operator is responsible for all periodic maintenance.
WARNING
Never operate a damaged or defective generator.

Oil Cont’d.

WARNING
Tampering with the factory set governor will void your warranty.

Spark Plugs

WARNING
Improper maintenance will void your warranty.

NOTE
Maintenance, replacement, or repair of emission control devices and systems may be performed by any non-road engine repair establishment or individual.

Complete all scheduled maintenance in a timely manner. Correct any issue before operating the generator.
NOTE
For service or parts assistance, contact our help line at 1-877-338-0999
Engine Maintenance
To prevent accidental starting, remove and ground spark plug wire before performing any service.
Oil
Change oil when the engine is warm. Refer to the oil specification to select the proper grade of oil for your operating environment. 1. Loosen the cover screws and remove the
maintenance cover. 2. Remove the oil filler cap. 3. Tilt the generator on its side and allow the oil to drain
completely. 4. Add 0.4 qt. (0.4 L) of oil and replace oil fill cap/
dipstick. DO NOT OVERFILL. 5. Reinstall the maintenance cover and tighten the
cover screws. 6. Dispose of used oil at an approved waste
management facility.
13

1. Remove the maintenance cover. 2. Remove the spark plug cable from the spark plug. 3. Use the spark plug tool that shipped with your
generator to remove the plug. Remove the spark plug access cap and insert the spark plug tool through this hole. 4. Remove the spark plug. 5. Inspect the electrode on the plug. It must be clean and not worn to produce the spark required for ignition. 6. Make certain the spark plug gap is 0.6 – 0.7 mm (0.024 – 0.028 in.).
0.6 – 0.7 mm 0.024 – 0.028 in.
7. Carefully thread the plug into the engine. 8. Use the spark plug tool to firmly install the plug. 9. Attach the spark plug cap to the plug. 10. Reinstall the spark plug access cap, and
maintenance cover.

73536i ENGLISH Air Filter

MAINTENANCE AND STORAGE
Spark Arrester Cleaning
1. Loosen M6x22 bolts to remove two pillars. 2. Remove 4 screws to remove the muffler cover
assembly. 3. Loosen the spark arrester clamp, remove the spark
arrester cover, and with a thin blade screwdriver remove the spark arrester. 4. Carefully remove the carbon deposits from the spark arrester screen with a wire brush.

1. Remove the maintenance cover. 2. Locate the air filter plastic cover. Remove the screw
using a Phillips head screwdriver. 3. Remove the foam element. 4. Wash in liquid detergent and water. Squeeze
thoroughly dry in a clean cloth. 5. Saturate in clean engine oil. 6. Squeeze in a clean, absorbent cloth to remove all
excess oil. 7. Place the filter in the assembly. 8. Reattach the air filter cover. 9. Reinstall the maintenance cover and tighten the
cover screw securely.
Cleaning
CAUTION

5. Replace the spark arrester if it is damaged. 6. Reattach spark arrester, cover assembly, and pillars.

DO NOT spray engine with water.

Water can contaminate the fuel system.
Use a damp cloth to clean exterior surfaces of the engine. Use a soft bristle brush to remove dirt and oil. Use an air compressor (25 PSI) to clear dirt and debris from the engine.

CAUTION
Failure to clean the spark arrester will result in degraded engine performance.

MAINTENANCE AND STORAGE

ENGLISH 73536i

Adjustments
The air-fuel mixture is not adjustable. Tampering with the governor can damage your generator and your electrical devices and will void your warranty. CPE recommends that you contact our service line at 1-877-338-0999 for all other service and/or adjustment needs.
Maintenance Schedule
Follow the service intervals indicated in the following maintenance schedule. Service your generator more frequently when operating in adverse conditions. Contact our help line at 1-877-338-0999 to locate the nearest Champion Power Equipment certified service dealer for your generator or engine maintenance needs.
Every 8 hours or daily Check oil level Clean around air intake and muffler
First 5 Hours Change oil
Every 50 hours or every season Clean air filter Change oil if operating under heavy load or in hot environments
Every 100 hours or every season Change oil Clean/Adjust spark plug Check/Adjust valve clearance* Clean spark arrester Clean fuel tank and filter*
Every 3 years Replace fuel line *To be performed by knowledgeable, experienced owners or Champion Power Equipment certified dealers.

Generator Maintenance
Make certain that the generator is kept clean and stored properly. Only operate the unit on a flat, level surface in a clean, dry operating environment. DO NOT expose the unit to extreme conditions, excessive dust, dirt, moisture or corrosive vapors.
CAUTION
DO NOT use a garden hose to clean the generator.
Water can enter the generator through the cooling slots and damage the generator windings.
Use a damp cloth to clean exterior surfaces of the generator. Use a soft bristle brush to remove dirt and oil. Use an air compressor (25 PSI) to clear dirt and debris from the generator. Inspect all air vents and cooling slots to ensure that they are clean and unobstructed.
Storage
The generator should be started at least once every 14 days and allowed to run for at least 20 minutes. For longer term storage, please follow these guidelines.
Generator Storage
1. Add a properly formulated fuel stabilizer to the tank. 2. Be sure all appliances are disconnected from the
generator. 3. Run the generator for a few minutes so the treated
fuel cycles through the fuel system and carburetor. 4. Turn the fuel valve to the “Off” position. 5. Let the generator run until fuel starvation has
stopped the engine. This usually takes a few minutes. 6. The generator needs to cool completely before
cleaning and storage. 7. Remove the spark plug cap, then pull the recoil grip 3
times to drain the gasoline from the carburetor jets. 8. Change the engine oil. 9. Remove the spark plug and pour about a tablespoon
of oil into the cylinder. Crank the engine slowly to distribute the oil and lubricate the cylinder. 10. Reattach the spark plug. 11.Store the unit in a clean, dry place out of direct sunlight.

73536i ENGLISH
Generator Storage Cont’d.
NOTE
Our engines work well with 10% or less ethanol blend fuels. When using blended fuels there are some issues worth noting: Ethanol-gasoline blends can absorb more water
than gasoline alone. These blends can eventually separate, leaving
water or a watery goo in the tank, fuel valve and carburetor. With gravity-fed fuel supplies, this compromised fuel can be drawn into the carburetor and cause damage to the engine and/or potential hazards. There are only a few suppliers of fuel stabilizer that are formulated to work with ethanol blend fuels. Any damages or hazards caused by using improper fuel, improperly stored fuel, and/ or improperly formulated stabilizers, are not covered by manufacture’s warranty. It is advisable to always shut off the fuel supply, run the engine to fuel starvation and drain the tank when the equipment is not in use for more than 30 days.
DANGER
Generator exhaust contains odorless and colorless carbon monoxide gas.
To avoid accidental or unintended ignition of your generator during periods of storage, the following precautions should be followed: When storing the generator for short or extended
periods of time make sure that the Engine Switch and the Fuel Valve are set in the OFF position.
16

SPECIFICATIONS

ENGLISH 73536i

US Patent # D656897, 8391012
Engine Specifications
Model . . . . . . . . . . . . . . . . . . . . . . YF149FD-330 Displacement . . . . . . . . . . . . . . . . . . . . . . . .80cc Type . . . . . . . . . . . . . . . . . . . . . . . .4-Stroke OHV Start Type . . . . . . . . . . . . . . . . . . . . . . . . . Recoil
Generator Specifications
Model . . . . . . . . . . . . . . . . . . . . . . . . . . . 73536i Running Wattage. . . . . . . . . . . . . . . . . 1700 Watts Starting Wattage . . . . . . . . . . . . . . . . . 2000 Watts AC Load . . . . . . . . . . . . . . . . . . . . . . . . . . 120 V Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . Single Frequency . . . . . . . . . . . . . . . . . . . . . . . . . 60 Hz Fuel Capacity . . . . . . . . . . . . . . . 1.0 gallon (3.8 L) Gross Weight . . . . . . . . . . . . . . . . 55.1 lb. (25 kg)
Net Weight. . . . . . . . . . . . . . . . . . 48.5 lb. (22 kg) Height . . . . . . . . . . . . . . . . . . . 16.3 in. (41.5 cm) Width . . . . . . . . . . . . . . . . . . . 13.2 in. (33.5 cm) Length. . . . . . . . . . . . . . . . . . . . .19.3 in. (49 cm)
Fuel
Fuel capacity is 1.0 gallon (3.8 L). Use regular unleaded gasoline with a minimum octane rating of 87 and an ethanol content of less than 10% by volume.
Oil
Use 10W-30 automotive oil. Oil capacity is 0.4 qt. (0.4 L). DO NOT OVERFILL. Please reference the following chart for recommended oil types for use in the generator.

Spark Plugs
OEM spark plug: NHSP E6RTC Replacement spark plug: NGK BPR6HS or equivalent Make certain the spark plug gap is 0.6 – 0.7 mm or (0.024 – 0.028 in.).
NOTE
Weather will affect engine oil and engine performance. Change the type of engine oil used based on weather conditions to suit the engine needs.
Maintenance Valve Clearance
Intake: 0.1 mm (0.004 in.) Exhaust: 0.1 mm (0.004 in.) Note: Tech bulletin regarding the valve adjustment procedure is on www.championpowerequipment.com.
An Important Message About Temperature
Your Champion Power Equipment product is designed and rated for continuous operation at ambient temperatures up to 40°C (104°F). When your product is needed your product may be operated at temperatures ranging from -15°C (5°F) to 50°C (122°F) for short periods. If the product is exposed to temperatures outside this range during storage, it should be brought back within this range before operation. In any event, the product must always be operated outdoors, in a well-ventilated area and away from doors, windows and other vents.

Degrees Celsiusº (Outside)

Full Synthetic 5W-30

Degrees Fahrenheitº (Outside)
17

73536i ENGLISH
Wiring Diagram

SPECIFICATIONS

SPECIFICATIONS
Parts Diagram

8 58
59

42 17

2 41

35 36 34 37 38 39

30 31 32

33 61

29 27

26 25 24 23 22 21 20

51 2 52 44 53 63 64 54 55

46 47 48

49 50

1 36 43

44 45 5 2

63 63

71 70

13 12 10 11

69 67

68 65

1 3
4

9 87

1 2

ENGLISH 73536i

73536i ENGLISH
# Part Number
1 81.200800.00.2 2 1.818.0514.3 3 81.200300.00.48 4 2.02.014 5 2.02.010 6 81.200601.00.2 7 81.200604.00
8 1.5789.0622.3
9 1.6177.1.06.3 10 1.5789.0612 11 81.221000.01 12 81.220003.01 13 1.5789.0615 14 81.200605.00 15 2.08.052.3 16 1.845.4220 17 122.210003.01 18 5.1840.002 19 81.212001.00
20 1.6177.1.04.3 21 81.210012.00 22 5.1110.000 23 5.1120.010 24 1.5783.0514.3 25 1.6170.02.3 26 81.01.5.2 27 1.6170.05.3 28 5.1200.308 29 81.210001.00 30 1.9074.4.0210.3
31 1.9074.4.0414.3 32 5.1130.001 33 81.210200.00 34 1.97.1.04.3 35 81.130200.00

Description

Qty

Art Cover

Screw M5×14, Green

Cover, Right, Yellow

Nut M6

Nut M5

Base Setting Component 1

Mounting Rubber, Base Setting

Flange Bolt M6×22, Green

Lock Nut M6, Flange, Green

Flange Bolt M6×12

Control Unit (120V/125V 60HZ)

Pintch, Control Unit

Flange Bolt M6×15

Motor Mount

Bolt M6×16, Green

Tapping Screw ST4.2X20

Plug, Control

Case, Power Supply

Control Box, Output Panel

Lock Nut M4, Flange, Green

Pintch, Signal

Receptacle (DC. 12V)

Receptacle 5-20R (Duplex)

Bolt M5×14, Green

Nut M2, Green

Output Panel

Nut M5, Green

D.C 8A Breaker, Push Button

Connect Port

Bolt/Washer Assembly M2×10, Green

Bolt/Washer Assembly M4×14, Green

Receptacle

Toroid Coil, Circular

Washer Ø4, Green

Pull Choke Assembly

# Part Number
36 1.818.0412.3 37 81.070001.00 38 5.1010.001.1 39 81.211100.00.2 40 81.126000.00 41 81.210200.01
42 81.211001.00
43 81.061200.00 44 2.02.015 45 81.200101.00.48 46 81.200200.00.48 47 81.403 48 81.070400.00 49 2.06.007
50 81.070011.00
51 81.071000.00.1
52 81.200401.00.48
53 81.070300.00
54 81.200402.00.48
55 1.818.0614.3 56 81.200502.00 57 81.200503.00 58 81.070100.00 59 1.5287.06.3 60 81.200700.00.2 61 81.200501.00.48 62 2.08.068.2 63 81.200102.00 64 81.200103.00 65 83.220001.00
66 81.220002.00
67 81.200602.00
68 81.200603.00
69 2.05.050 70 122.190600.00 71 1.5783.0520
72 9.1600.004

Parts List

Description

Qty

Screw M4×12, Green

Knob, Fuel valve

Ignition Switch

Operate Panel

Ignition Assembly

Toroid Coil, Square

Control Box, Operation Panel

Guide, Rope

Nut M6

Front Cover, Yellow

Cover, Left, Yellow

Engine, 80cc

Fuel Valve

Clamp Ø8 x b6

Fuel Pipe, Ø4.5 x Ø8.5 x 185

Fuel Tank, 3.8L, Black

Supporter, Rear Cover, Yellow

Fuel Filter, Wire Mesh

Protector, Rear Cover, Yellow

Screw M6×14, Green

Spillway, Fuel Tank

Plug

Fuel Tank Cap

Giant Washer Ø6, Green 4

Handle Assembly

Cover, Top, Yellow

Flange Bolt M5×13

Rotundity Jacket

Groove Jacket

Protector, Control Unit

Mount Rubber, Control Unit

Mounting Rubber, End Cover

Mounting Rubber, Enging

Clamp, Wire

Rectifier

Bolt M5×20

12V DC Battery Charging Cable

SPECIFICATIONS
Engine Parts Diagram

106

50 51

33 34 35

52 53 13 54 55 56 57

107

64 66

29 30 1 31 32

1 36 37 38 39 40 41 42 43 44 45 46 47

59 97
60 61 47 62

78 79 80 81 82 83 84

105
77 76

85 3

28 27 26

66 67 68 69 70

13 25 24 23 22 21 89 1 20 19 18 17 16 15 14 13 12 11

73
71 72 104 58 70 91 92
93 94
95

13
98 99 100 101 102 103

ENGLISH 73536i

73536i ENGLISH
# Part Number
1 1.5789.0612 2 81.061000.00 3 1.5789.0615 4 2.02.013 5 81.080100.00 6 2.02.018 7 1.16674.0512 8 81.080001.00 9 81.060001.00 10 2.11.019 11 81.030100.00 12 81.123000.01 13 1.5789.0620 14 1.276.6204 15 81.030013.01 16 81.030013.00 17 81.050100.00 18 2.14.013 19 2.04.002 20 81.030008.00 21 81.127000.00 22 81.030006.00 23 81.030007.00 24 81.122000.00 25 1.16674.0612 26 81.191200.02 27 1.5789.0635 28 81.191100.00 29 81.190006.01 30 81.190006.00 31 1.5789.0622.3 32 81.190002.00 33 2.06.011 34 81.101501.00 35 81.101300.00 36 81.081002.00 37 81.190001.00 38 2.09.007 39 81.050003.00 40 81.050200.00 41 81.050300.02 42 81.050005.02 43 81.040100.00 44 81.040013.00 45 81.040005.00 46 2.15.005(E6RTC) 47 2.01.027 48 1.845.4817 49 81.081300.00 50 81.081200.00 51 1.6175.06.3 52 81.101100.00 53 81.100001.00 54 81.081100.00 55 81.081003.00 56 81.081001.00 57 81.080003.00

Description
Flange Bolt M6 x 12 Recoil Assembly Flange Bolt M6 x 15 Nut M6 Fan Cover Nut M12 x 1.25 Flange Bolt M5 x 12 Cooling Fan Pulley, Starter Oil Seal 20 x 35 x 5 Crankcase Ignition Coil Flange Bolt M6 x 20 Bearing 6204 Seal Strip 2, Crankcase Cover Seal Strip 1, Crankcase Cover Crankshaft Woodruff Key 3 x 5 x 13 Dowel Pin 8 x 14 Gasket, Crankcase Cover Oil Level Sensor Plate, Coil Cover, Crankcase Trigger Assembly Flange Bolt M6 x 12 Stator Component Flange Bolt M6 x 35 Rotor Component Rubber Sleeve 2, End Cover Rubber Sleeve 1, End Cover Flange Bolt M6 x 22 End Cover, Motor Clamp, Ø25 x b10 Cap, Spark Arrester Spark Arrester Rubber Seal Sleeve Cooling Fan, Rotor Circlip Ø13.5 x Ø1 Pin, Piston Connecting Rod Piston Ring Set Piston Camshaft Lifter, Valve Push Rod Spark Plug E6RTC Stud Bolt M6 x 27 Tapping Screw Muffler Protector Assembly Muffler Protector Assembly Nut M6 Muffler Gasket, Exhaust Pipe Muffler Protector, Side Fastening Insert Muffler Protector Seal Air Duct

Qty.
7 1 8 1 1 2 4 1 1 2 1 1 12 2 1 1 1 2 4 1 1 1 1 1 2 1 2 1 1 1 4 1 1 1 1 1 1 2 1 1 1 1 1 2 2 1 6 4 1 1 2 1 1 1 1 1 1

# Part Number
58 1.6177.1.06.3 59 81.020001.00 60 81.021000.01 61 81.020002.00 62 81.080200.00 63 1.5789.0650 64 81.010100.00 65 81.030009.00 66 2.01.026 67 81.130002.00 68 81.130001.00 69 81.130003.00 70 81.130000.00 71 81.130004.00 72 81.090004.00 73 81.090003.00 74 81.091100.00 75 81.091003.00 76 81.091200.00 77 2.08.053 78 2.02.009 79 81.040012.00 80 81.040009.00 81 81.040016.00 82 83.040014.01 83 83.040001.01 84 81.040017.00 85 83.040003.01 86 81.040002.00 87 81.040006.00 88 81.031000.00 89 1.5789.0608 90 81.030035.00 91 1.9074.4.0535 92 1.818.0306.1 93 1.9074.3.0510 94 81.130007.00 95 81.130010.00
81.131000.00 96
81.131000.02 97 2.06.010 98 81.132200.00 99 1.9074.1.0408 100 81.132100.00 101 81.130005.00 102 81.130008.00 103 81.130006.00 104 81.090005.00 105 81.091000.00 106 81.101000.00 107 81.010000.00

Engine Parts List

Description
Flange Lock Nut M6 Breather Tube Cover, Cylinder Head Gasket, Cylinder Head Cover Air Shroud, Cylinder Flange Bolt M6 x 50 Cylinder Head Gasket, Cylinder Head Stud Bolt M6 x 88 Gasket, Insulator Insulator, Carburetor Gasket, Carburetor Carburetor Assembly Gasket, Air Cleaner Pipe, Air Cleaner Joint, Breather Pipe Base, Air Cleaner Element, Air Cleaner Cover, Air Cleaner Bolt M6 x 20 Nut M5 x 0.5, Lock Screw, Valve Adjustment Rocker Arm, Intake Valve Shaft, Rocker Arm Valve Collet Retainer, Valve Spring Oil Seal, Valve Spring, Valve Valve, Intake Valve, Exhaust Oil Dipstick Assembly Flange Bolt M6 x 8 Oil Nipple Screw M5 x 35 Screw M3 x 6 Screw M5 x 10 Clamp Board, Choke Control Line Spring, Connecter
Carburetor
Clamp, Ø10.5 x Ø1 Stepper Motor Screw M4 x 8 Stepper Motor Base Support, Stepper Motor Connecter, Choke Valve Axis Brace, Support Plate Clamp Board, Air Filter Tube Air Cleaner Assembly Muffler Assembly Cylinder Head Assembly

Qty.
6 1 1 1 1 4 1 1 2 1 1 1 1 1 1 1 1 1 1 1 2 2 2 1 2 2 1 2 1 1 1 1 1 2 2 1 1 1
1
2 1 2 1 1 1 2 1 1 1 1

TROUBLESHOOTING

Problem
Generator will not start
Generator will not start; Generator starts but runs roughly
Generator shuts down during operation

Cause
No fuel Faulty spark plug Unit loaded during start up Low oil level
Choke in the wrong position Spark plug wire loose Out of fuel Low oil level

Generator cannot supply enough power or overheating

Generator is overloaded Insufficient ventilation

No AC output Repeated circuit breaker tripping

Cable not properly connected Connected device is defective Circuit breaker is open Loose wiring Other Overload

Faulty cords or device

For further technical support:
Technical Service Mon Fri 8:30 AM 5:00 PM (PST/PDT) Toll Free: 1-877-338-0999 [email protected]

ENGLISH 73536i
Solution
Add fuel Replace spark plug Remove load from unit Fill crankcase to the proper level Place generator on a flat, level surface Adjust choke Attach wire to spark plug Fill fuel tank Fill crankcase to the proper level. Place generator on a flat, level surface Review load and adjust. See “Power Management” Check for air restriction. Move to a well ventilated area Check all connections Replace defective device Reset circuit breaker Inspect and tighten wiring connections Contact the help line Review load and adjust. See “Power Management” Check for damaged, bare or frayed wires. Replace defective device

WARRANTY*
CHAMPION POWER EQUIPMENT 3 YEAR LIMITED WARRANTY
Warranty Qualifications
To register your product for warranty and FREE lifetime call center technical support please visit: https://www.championpowerequipment.com/register To complete registration you will need to include a copy of the purchase receipt as proof of original purchase. Proof of purchase is required for warranty service. Please register within ten (10) days from date of purchase.
Repair/Replacement Warranty
CPE warrants to the original purchaser that the mechanical and electrical components will be free of defects in material and workmanship for a period of three years (parts and labor) from the original date of purchase and 270 days (parts and labor) for commercial and industrial use. Transportation charges on product submitted for repair or replacement under this warranty are the sole responsibility of the purchaser. This warranty only applies to the original purchaser and is not transferable.
Do Not Return The Unit To The Place Of Purchase
Contact CPE’s Technical Service and CPE will troubleshoot any issue via phone or e-mail. If the problem is not corrected by this method, CPE will, at its option, authorize evaluation, repair or replacement of the defective part or component at a CPE Service Center. CPE will provide you with a case number for warranty service. Please keep it for future reference. Repairs or replacements without prior authorization, or at an unauthorized repair facility, will not be covered by this warranty.
Warranty Exclusions
This warranty does not cover the following repairs and equipment: Normal Wear Products with mechanical and electrical components need periodic parts and service to perform well. This warranty does not cover repair when normal use has exhausted the life of a part or the equipment as a whole. Installation, Use and Maintenance This warranty will not apply to parts and/or labor if the product is deemed to have been misused, neglected, involved in an accident, abused, loaded beyond the product’s limits, modified, installed improperly or connected incorrectly to any electrical component. Normal maintenance is not covered by this warranty and is not required to be performed at a facility or by a person authorized by CPE.

Other Exclusions
This warranty excludes: Cosmetic defects such as paint, decals, etc.
Wear items such as filter elements, o-rings, etc.
Accessory parts such as starting batteries, and storage covers.
Failures due to acts of God and other force majeure events beyond the manufacturer’s control.
Problems caused by parts that are not original Champion Power Equipment parts.
When applicable, this warranty does not apply to products used for prime power in place of a utility.
Limits of Implied Warranty and Consequential Damage
Champion Power Equipment disclaims any obligation to cover any loss of time, use of this product, freight, or any incidental or consequential claim by anyone from using this product. THIS WARRANTY AND THE ATTACHED U.S. EPA and/or CARB EMISSION CONTROL SYSTEM WARRANTIES (WHEN APPLICABLE) ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. A unit provided as an exchange will be subject to the warranty of the original unit. The length of the warranty governing the exchanged unit will remain calculated by reference to the purchase date of the original unit. This warranty gives you certain legal rights which may change from state to state or province to province. Your state or province may also have other rights you may be entitled to that are not listed within this warranty.
Contact Information
Address Champion Power Equipment, Inc. 12039 Smith Ave. Santa Fe Springs, CA 90670 USA www.championpowerequipment.com Customer Service Toll Free: 1-877-338-0999 [email protected] Fax no.: 1-562-236-9429 Technical Service Toll Free: 1-877-338-0999 [email protected] EMERGENCY 24 HOUR SUPPORT: 1-562-204-1188

*Except as otherwise stipulated in any of the following enclosed Emission Control System Warranties (when applicable) for the Emission Control System: U.S. Environment Protection Agency (EPA) and/or California Air Resources Board (CARB).

CHAMPION POWER EQUIPMENT, INC. (CPE), THE UNITED STATES ENVIRONMENT PROTECTION AGENCY (U.S. EPA) AND THE CALIFORNIA AIR RESOURCES BOARD (CARB) EMISSION CONTROL SYSTEM WARRANTY
Your Champion Power Equipment (CPE) engine complies with both the U.S. EPA and state of California Air Resources Board (CARB) Exhaust and Evaporative emissions regulations.
YOUR WARRANTY RIGHTS AND OBLIGATIONS:
The US EPA, California Air Resources Board, and CPE are pleased to explain the Federal and California Exhaust and Evaporative Emission Control Systems Warranty on your 2020 small off-road engine (SORE) and engine powered equipment. In California, new equipment that use small off-road engines (SORE) must be designed, built and equipped to meet the State’s stringent anti smog standards. In the other states, new engines and equipment must be designed, built and equipped, at the time of sale, to meet U.S. EPA regulations for small offroad engines (SORE). CPE must warrant the exhaust and evaporative emission control system on your small off-road engine (SORE) for the period listed below, provided there has been no abuse, neglect, unapproved modification, or improper maintenance of your equipment leading to the failure of the exhaust and evaporative emission control systems. Your evaporative emission control system may include parts such as: carburetors, fuel tanks, fuel lines, (for liquid fuel and fuel vapors), fuel caps, valves, canisters, filters, clamps, connectors, and other associated components. Also included for your exhaust emission control system may be fuel-injection system, the ignition system, catalytic converter and other exhaust emission related assemblies. Where a warrantable condition exits, CPE will repair your small off-road engine (SORE) at no cost to you including diagnosis, parts and labor.
MANUFACTURER’S WARRANTY COVERAGE:
This exhaust and evaporative emission control system is warranted for two years. If any exhaust and evaporative, emission related part on your engine or equipment is defective in, the part will be repaired or replaced by CPE.
OWNER WARRANTY RESPONSIBILITIES:
As the small off-road engine (SORE) owner, you are responsible for the performance of the required maintenance listed in your Owner’s Manual. CPE recommends that you retain all your receipts covering maintenance on your small off-road engine (SORE), but CPE cannot deny warranty coverage solely for the lack of receipts. As the small off-road engine (SORE) owner, you should be aware that CPE may deny you warranty coverage if your small, off-road engine (SORE) or a part has failed due to abuse, neglect, improper maintenance or unapproved modifications. You are responsible for presenting your small off-road engine to an Authorized CPE distribution center, service center or alternative service outlet as described in (3)(f.) below or CPE dealer or CPE, Santa Fe Springs, Ca. as soon as the problem exists. The warranty repairs shall be completed in a reasonable amount of time, not to exceed 30 days. If you have any questions regarding your warranty coverage, you should contact:
Champion Power Equipment, Inc. Customer Service 12039 Smith Ave.
Santa Fe Springs, CA 90670 1-877-338-0999
[email protected]

EXHAUST AND EVAPORATIVE EMISSION CONTROL SYSTEM WARRANTY
The following are specific provisions relative to your Exhaust and Evaporative Emission Control System (ECS) Warranty Coverage.
1. APPLICABILITY: This warranty shall apply to 1995 and later model year California small off-road engines (SORE) (for other states, 1997 and later model year engines). The ECS Warranty Period shall begin on the date the new engine or equipment is delivered to its original, end-use purchaser, and shall continue for 24 consecutive months thereafter.
2. GENERAL EMISSIONS WARRANTY COVERAGE CPE warrants to the original, end-use purchaser of the new engine or equipment and to each subsequent purchaser that each of its small off-road engines (SORE) is:
2a. Designed, built and equipped to conform to U.S. EPA emissions standards for spark-ignited engines at or below 19 kilowatts and all applicable regulations adopted by the California Air Resources Board, and
2b. Free from defects in materials and workmanship that cause the failure of a warranted part to be identical in all material respects to the part as described in the engine manufacturer’s application for certification for a period of two years.
3. THE WARRANTY ON EXHAUST AND EVAPORATIVE EMISSION-RELATED PARTS WILL BE INTERPRETED AS FOLLOWS:
3a. Any warranted part that is not scheduled for replacement as required maintenance in the Owners Manual shall be warranted for the ECS Warranty Period. If any such part fails during the ECS Warranty Period, it shall be repaired or replaced by CPE according to Subsection “d” below. Any such part repaired or replaced under the ECS Warranty shall be warranted for any remainder of the ECS Warranty Period.
3b. Any warranted, exhaust and evaporative emissions-related part which is scheduled only for regular inspection as specified in the Owners Manual shall be warranted for the ECS Warranty Period. A statement in such written instructions to the effect of “repair or replace as necessary”, shall not reduce the ECS Warranty Period. Any such part repaired or replaced under the ECS Warranty shall be warranted for the remainder of the ECS Warranty Period.
3c. Any warranted, exhaust and evaporative emissions-related part which is scheduled for replacement as required maintenance in the Owner’s Manual shall be warranted for the period of time prior to the first scheduled replacement point for that part. If the part fails prior to the first scheduled replacement, the part shall be repaired or replaced by CPE according to Subsection “d” below. Any such exhaust and evaporative emissions-related part repaired or replaced under the ECS Warranty, shall be warranted for the remainder of the ECS Warranty Period prior to the first scheduled replacement point for such emissions-related part.
3d. Repair or replacement of any warranted, exhaust and evaporative emissions-related part under this ECS Warranty shall be performed at no charge to the owner at a CPE Authorized Service Outlet.
3e. The owner shall not be charged for diagnostic labor which leads to the determination that a part covered by the ECS Warranty is in fact defective, provided that such diagnostic work is performed at a CPE Authorized Service Outlet.
3f. CPE shall pay for covered exhaust and evaporative emissions warranty repairs at non-authorized service outlets under the following circumstances:
i. The service is required in a population center with a population over 100,000 according to U.S. Census 2000 without a CPE Authorized Service Outlet AND
ii.The service is required more than 100 miles from a CPE Authorized Service Outlet. The 100 mile limitation does not apply in the following states: Alaska, Arizona, Colorado, Hawaii, Idaho, Montana, Nebraska, Nevada, New Mexico, Oregon, Texas, Utah and Wyoming.
3g. CPE shall be liable for damages to other original engine components or approved modifications proximately caused by a failure under warranty of an emission-related part covered by the ECS Warranty.
3h. Throughout the ECS Warranty Period, CPE shall maintain a supply of warranted exhaust and evaporative emission-related parts sufficient to meet the expected demand for such exhaust and evaporative emission-related parts.
3i. Any CPE Authorized and approved exhaust and evaporative emission-related replacement part may be used in the performance of any ECS Warranty maintenance or repair and will be provided without charge to the owner. Such use shall not reduce CPE’s warranty obligation.
3j. Unapproved add-on or modified parts may not be used to modify or repair a CPE engine. Such use voids this ECS Warranty and shall be sufficient grounds for disallowing an ECS Warranty claim. CPE shall not be liable hereunder for failures of any warranted parts of a CPE engine caused by the use of such an unapproved add-on or modified part.

EMISSION-RELATED PARTS INCLUDE THE FOLLOWING: (using those portions of the list applicable to the engine)

Systems covered by this warranty
Fuel Metering System Air Induction System Ignition System Exhaust System Miscellaneous Parts Evaporative Emissions

Parts Description
Fuel regulator, Carburetor and internal parts Air cleaner, Intake manifold Spark plug and parts, Magneto ignition system Exhaust manifold, catalytic converter Tubing, Fittings, Seals, Gaskets, and Clamps associated with these listed systems. Fuel Tank, Fuel Cap, Fuel Lines (for liquid fuel and fuel vapors), Fuel Line Fittings, Clamps, Pressure Relief Valves, Control Valves, Control Solenoids, Electronic Controls, Vacuum Control Diaphragms, Control Cables, Control Linkages, Purge Valves, Gaskets, Liquid/Vapor Separator, Carbon Canister, Canister Mounting Brackets, Carburetor Purge Port Connector

TO OBTAIN WARRANTY SERVICE:
You must take your CPE engine or the product on which it is installed, along with your warranty registration card or other proof of original purchase date, at your expense, to any Champion Power Equipment dealer who is authorized by Champion Power Equipment, Inc. to sell and service that CPE product during his normal business hours. Alternate service locations defined in Section (3)(f.) above must be approved by CPE prior to service. Claims for repair or adjustment found to be caused solely by defects in material or workmanship will not be denied because the engine was not properly maintained and used.
If you have any questions regarding your warranty rights and responsibilities, or to obtain warranty service, please write or call Customer Service at Champion Power Equipment, Inc.
Champion Power Equipment, Inc. 12039 Smith Ave.
Santa Fe Springs, CA 90670 1-877-338-0999
Attn.: Customer Service [email protected]

References

P65Warnings.ca.gov